Time To First Fix
Cold status 45s£¬warm
12¡ª24V input, 5V output
input, 5V output
Chargeable changeable 3.7V 800mAh Li-ion battery
-40¡ãC to +85¡ãC
-20¡ãC to +55¡ãC
Make sure that there is no call transfer and call
display is on, and PIN code off. The SMS message must in
Text format, can¡¯t be identified for
5.1.1 Open the rear cover, and pick out the battery.
5.1.2 Push the foil up according the arrow on the foil
and load the miscro SD card and push back.
the SIM card into the holder as picture shows.
5.2 Battery and Charger
Do charge the battery to capacity in 8 -12 hours for
first use. Please use the battery and charger provided
by the manufacturer. This unit adopts
built-in Li-ion battery, and full battery will support around 48 hours
use on end. After first use, the battery can be charged
fully in 3-5hours.
For it¡¯s Li-ion battery, which contains harmful
chemicals and may burst, please don¡¯t bump, puncture it
violently and keep it off fire.
Please charge the battery in time to keep it working
Put the SIM card
and battery in place.
b: Turn on the unit outdoors by pressing the
¡°on/off¡± button until the indicator is on.
For first use, please initialize the unit and restore it
to default setting. (Please refer to 5.4 for
In 10 or 40
seconds, the unit will begin to work and acquire the GSM
signals as well as the GPS signals. The indicator will
every 4 seconds when the unit has received the signals,
otherwise it will keep on.
When this unit
receives GPS signals normally, you can use it and do all
the following settings.
¡°begin+password¡± in SMS to the unit, it will reply
¡°begin ok¡± and initialize all the settings. (Default
example, send SMS¡°
to the tracker via a cell phone, If succeeded,
OK¡± is returned by the device in SMS. If there is
something wrong then SMS ¡°begin fail¡± is received, check
out the format of
commands sent and password as well.
Attention, begin+123456,the symbol¡°+¡±
in the following, please don't add
begin123456 in SMS. This description is only for quick
argument, ¡°space¡± not the word space, it means press the
5.4.2 No GPS signal in house, in high
buildings, in metals, when testing, you should put the
tracker outside house. Spacious places have strong
password+old password+space+new password to change the
Be sure keep the new password in mind, you have to
upload the software to restore the original setting in
case of losing the new password.
Make sure the new password is in 6 digits, or else the
tracker can not recognize the password.
There are only 5 numbers able to be authorized.
Call the tracker for 10 times, it will make the cell
phone number as the authorized number automatically.
5.6.2 Send SMS admin+password+space+cell phone
number to set up a authorized number. The other
authorized numbers should be set by the first authorized
number. If the number is successfully authorized, the
unit will reply ¡°admin ok!¡± in SMS.
5.6.3 Send SMS noadmin+password+space+authorized
number to delete the authorized number.
5.6.4 For roaming purpose, you have to add your
country code ahead of the cell phone number, for
example, please send admin123456
008613322221111 to tracker to set 13322221111 as an authorized number.
If there is no authorized number, when any number dials
up the unit, it will report a Geo-info; If there is
already an authorized number, then it
will not respond when an unauthorized number calls it up.
When an authorized number dials up the unit, it will
hang up and report a real-time Geo-info as below:
*Tracking location, When GPS signals is weak, the
position of latitude and longitude included in the SMS
is the position that the tracker received GPS signals at
last. If it is different with its exact current
location, pay attention to check the time included in
the SMS you got.
5.8 Get location in real
5.8.1 You must set up the APN of your local GSM
network for the SIM card in tracker first before using
this function, if there is user name and
password for GPRS login, Please refer to 5.19.1 and 5.19.2 to configure
the APN, user name and password for GPRS login.
5.8.2 After configure the APN, send address+password
to device, it will reply SMS including real
street/address name. For example: No.113,
Nantou Guankou 2nd Rd. Nanshan district, Shenzhen, Guangdong,
Geo-info at 30s intervals to the authorized numbers for
Send SMS command
¡°fix030s005n +password¡± to the
tracker device, it will report the Geo-info at 30s
intervals for 5 times. (s:second,
m:minute, h:hour). This command set must be in 3 digits and the
maximum value is 255.
Send SMS ¡°fix030s***n+password¡± to
the tracker device, it will reply the Geo-info
continuously at 30 seconds intervals.
Cancellation: Send SMS
¡°nofix+password¡± to the tracker device to cancel the
Note: the interval must
not less than 20s.
Location based service (LBS)
When the tracker device
doesn¡¯t received valid GPS signals, tracker will
positioning by location based service, the messages
GPS coordinates of the last position in SMS mode, but the LAC in message
is the current new position, the location can be seen by
LAC code in the menu ¡°Manual Track¡± of web platform
www.gpstrackerxy.com, you can also send
command ¡°address+password¡± to
tracker to get the newest absolute address and GPS coordinates as well;
tracker will automatically switch to track by location
based service in
GPRS mode, and actualized on the map of web server with LBS mark. And
there may be some inaccuracy with actual location by LBS
the bias depends on GSM reception.
This feature can be used normally in most areas
according to the signal of GSM network. It may not be
available in some areas.
Monitor (Voice Surveillance)
5.11.1 The command to
switch between Track and Monitor are ¡°tracker¡± and ¡°
5.11.2 The default mode
is ¡°track¡± (Track mode).
5.11.3 Send SMS
¡°monitor+password¡± to the unit, and it will reply
¡°monitor ok!¡± and switch to ¡°monitor¡± mode.
5.11.4 Send SMS
¡°tracker+password¡± to the unit, it will reply ¡°tracker
ok!¡± and restore to ¡°track¡± mode.
5.12.1 Auto Storage£ºWhen
the tracker devices lost GSM signals or fall offline
from GPRS, tracker will store the tracking position and
automatically in the flash upon the pre-set condition, when GSM signals
get back, all the event alerts will be auto-sent to the
or monitoring platform (server), but the stored tracking data should be
loaded to the monitoring platform via SMS command.
5.12.2 Storage upon
times: Send SMS: ¡°save030s005n+password¡± to the tracker
unit, it will reply ¡°save ok¡±, and will store the lat,
locations every 30 seconds for 5 times. (S: second, m: minute; h: hour).
sms:¡±save030s***n+ password¡± to tracker device, it will
reply ¡°save ok¡±.
Clearance: send SMS: ¡°clear+ password¡± to tracker
device, it will reply ¡°clear ok¡±.
slot, capacity according to the Micro SD
5.12.6 The stored data
can be copied to computer via the USB cable which put in
the package. The route of the stored data can be seen by
importing data in the menu ¡° Data Import¡± of web platform
5.13: Inbuilt shock sensor
It is disabled as
default, send ¡°shock+password to tracker, tracker will
reply ¡°shock ok!¡±, ¡°sensor alarm+lat/long¡± will send to
phone when tracker is being shocked, and one alarm for each shock event
¡°noshock+password¡± to cancel the shock sensor alarm.
5.14 Data Load
5.14.1 Current date Load: Send SMS: ¡°load+ password¡±
to tracker device, it will reply: ¡°load
ok¡± if the device
is working well under GPRS mode; if not, it will reply
¡°load fail! Please check gprs¡± that means device does
not work under
5.14.2 Specified date
Send SMS: ¡°load+ password+ space+ year month date¡± to
tracker device, it will reply: ¡°load ok¡± and load
the tracking data to the monitoring platform upon the valid time you
choose. For Example: send SMS: ¡°load123456 20110425¡± to
device, means to load the tracking data of 25th April 2011 to monitoring
Set up a
geo-fence for the unit to restrict its movements within
a district. The unit will send the message to the
authorized numbers when it
breaches the district.
Set up: When the unit stays immobile in a place for 3-10
minutes, the user can Send SMS:
¡°stockade+password+space+latitude,longitude; latitude,longitude¡± to unit
to set the restricted district. In case of breach, it
will send SMS
¡°stockade!+geo-info¡± to the authorized numbers.
Remark: The first latitude&longitude is coordinate of
the top left corner of the Geo-fence, while the second
latitude&longitude is the coordinate
of the bottom right corner. It will alarm one
time in each setting.
Cancel: Send SMS:¡± nostockade+password¡± to
deactivate this function.
5.16 Movement alert
5.16.1 Set up: When the unit stays immobile in a
place for 3-10 minutes, the user can send SMS:
¡°move+password¡± to the unit, then the unit
will reply ¡°move ok!¡±. In case of such a movement£¨the
unit default distance is 200M£©,
it will send SMS ¡°Move+ Geo-info¡± to the
numbers every 3
minutes. It will alarm one time in each setting.
Cancel: Send SMS:¡± nomove+password¡± to deactivate the
5.17 Overspeed alert:
Set up: Send SMS:¡± speed+password+space+080¡± to the unit
(suppose the speed is 80km/h), and it will reply ¡°speed
the target moves exceeding 80 km/h, the unit will send SMS
:¡±speed+080!+Geo-info¡± to the authorized numbers every 3
minutes. It will alarm
one time in each setting.
5.17.2 Cancel: Send SMS
¡°nospeed+password¡± to deactivate the overspeed alarm.
Remark: The recommended
speed should be not less than 30km/h. For below that
rate, it will be effected the accuracy by gps signals
5.18 SOS button
SOS for 3 seconds, it will send ¡°help me!+ Geo-info¡± to
all the authorized numbers every 3 minutes. It will stop
sending such a SMS
when any authorized number reply SMS ¡°help me!¡± to the tracker.
5.19 Low battery alert
When GPS device battery is
going to be 3.7V, it will send SMS:¡±low battery+Ge-info¡±
in 3 minutes interval.
5.20 State Checking
Send SMS:¡±check+password¡± to
the tracker device, it will reply the recent status via
SMS as: GSM: 100% GPS: OK/NO GPRS: ON/OFF
5.21 IMEI checking:
command "imei+password" to the unit. E.g.: Send SMS
command "imei123456" to the unit, an IMEI number in 15
digits will be
replied to your cell phone.
5.22 Terminal (local) Time
Send SMS ¡°time+space+zone+password+space+local time
Send SMS ¡°time zone123456 8¡± (time zone of China).
If the local
time zone is negative as ¡°-8¡±, then it should set as SMS:
5.23 GPRS setting
send SMS via cell phone to set up IP, port and APN
before starting GPRS.
Setting up APN
126.96.36.199 APN standards for Access Point Name and
differs from country to country. For more information
about the local APN, inquire with your
local GPRS network operator.
188.8.131.52 Text the tracker a SMS ¡°APN+password +
Space + your local APN¡± via a cell phone and if
succeeded in setup, the tracker will return
the message ¡°APN OK¡±.
184.108.40.206 e.g. send SMS command ¡°APN123456 CMNET¡±. If
succeeded, ¡°APN OK¡± is returned by the tracker in SMS.
Notes: 123456 refer to password of tracker and CMNET is
the APN of China Mobile (One of GSM Operator in china).
GPRS User ID and password Setup
220.127.116.11 In most countries, the user name and
password involving GPRS login are not
compulsorily necessary, therefore, the entry can be
skipped. For those countries requiring user name and
password, please configure as
18.104.22.168 Send SMS
¡°user,password ok¡± is returned by the tracker in SMS.
22.214.171.124 For instance, send SMS ¡°up123456 jonnes
666666¡± to the tracker, and if succeeded, the tracker
returns ¡°user, password OK¡±
IP and port setup
126.96.36.199 Send SMS as below via a cell phone: adminip
+password + Space + IP Address + Space + Port Number.
If succeeded, ¡°adminip
OK¡± is returned by the device in SMS.
188.8.131.52 e.g, Send SMS command ¡°adminip123456
184.108.40.206 9000¡± to the tracker device, If
succeeded, ¡°adminip OK¡± is returned
by the device in SMS.( 123456 is default password£¬220.127.116.11
5.23 Modes switch between ¡°SMS¡±
The default mode is ¡°SMS¡±
Send SMS ¡°GPRS+password¡± to the unit, and it will
reply ¡°GPRS ok!¡± and switch to ¡°GPRS¡± mode.
¡°SMS+password¡± to the unit, it will reply ¡°SMS ok!¡± and
restore to ¡°SMS¡± mode.
Web platform and PC installation tracking software
Web based platform
www.gpstrackerxy.com. Configuration IP:
18.104.22.168 Port: 9000. Please check ¡°software
manual¡± included in the CD for detailed operation information.
PC based installation tracking software included in the
CD in package.
comply with the instructions to extend the unit life:
Keep the unit dry. Any liquid, i.e. rain, moisture, may
destroy or damage the inside circuitry.
Don¡¯t use & store the unit in dusty places.
Don¡¯t put the unit in overheated or overcooled
Handle carefully. Don¡¯t vibrate or shake it
Clear the unit with a piece of dry cloth. Don¡¯t clean in
Don¡¯t paint the unit, this may cause some foreign
materials left in between the parts.
Don¡¯t disassemble or refit the unit.
Please use the battery and charger provided by
manufacturer. Using other batteries and chargers will
cause unwanted situation.
7 Faults & The solutions
Check the battery and see if it is fully charged
In existence of an authorized number, an
number dials up the unit. Please initialize the
unit and re-set up
the authorized numbers.
No GSM Signal
Please make sure SIM Card is GSM Net and
installed correctly; also call display should be
on; but no call transfer and PIN code off.