Working Based on existing GSM/GPRS network and GPS
satellites, Set multiple functions of security,
tracking, monitoring surveillance, emergency alarms and
product can locate and monitor any remote targets by SMS or
1.2.1 Taillights shape, easy to hide, waterproof design, and
1.2.2 Built-in GSM, GPS antenna.
1.2.2 Support GPS and LBS (location based service) double
1.2.3 Support SMS / GPRS / Internet Network data
transmission (GPRS/Internet instructions includes in CD in
1.2.4 Support configures the settings remotely
1.2.5 Set multiple functions of security, tracking,
monitoring surveillance, emergency alarms and
management in its entirety.
Used widely for motorcycle and other moving objects
This device is divided into the following two types according
accessories and its function:
Type A: 8 PIN
hardness, tracking, monitoring, ACC,
cut off oil and power.
Type B: Add remote controller to ARM & DISARM
on the basis of type A.
Optional, Type A/B
Optional, type B
Time To First
3.7V 1000mAh Li-ion battery
Please ask the qualified engineers to install it.
not install it in an environment which is over GSM performance
Pay attention to make installation location preventing water and
Find the 8 PIN harness and insert it into the corresponding
holes of the products, and connect the wires with the original
car circuit showing below:
6.1.5 Note: The
pink wire can be connected to the car original siren; or
connected to the siren buying with the tracker. (Siren is an
6.1.6 Please install
the SOS button on the place driver can touch.
6.2.1 Use the
screwdriver accompanied with the device to open sealed buckle
and insert the SIM card, the SIM card is placed correctly if
heard the sound of lock, the SIM will automatically pop up if
press it gently. Then, put sealed buckle back
6.2.2 Please make
sure the SIM card is for GSM network and able to execute the
function of incoming calls display, no calls can be diverted and
the PIN code is locked. The SMS format must be TXT format, and
can’t recognize the PDU format.
positive & negative wire, red / black ones, with 12V or 24V car
power system, wait for 1 minute after connecting power to wait
tracker works normal, and then turn on the backup battery
Send “begin+password” in SMS to the unit, it will reply “begin
ok” and initialize all the settings. (Default password: 123456)
For example, send SMS
“begin123456” to the tracker via a cell phone, if succeeded, if
will reply “begin ok”.
6.5.1 Send SMS
“password+old password+space+new password” to the unit to change
For example: send SMS
“password123456 888888” to the unit. If succeeded, “password ok”
will reply to your cell phone from the device tracker.
6.5.2 Be sure to keep
the new password in mind, you have to upload the software to
restore the original setting in case of losing the new password.
6.5.3 Attention: Make
sure the new password is in 6 digits Arabic numbers, or else the
tracker cannot recognize the password.
6.5.4 The “+” in the
command, please don’t type “+”, space means press the space
keyboard on your cell phone
There are 5 numbers
to be allowed to authorize in the tracker at most.
6.6.1 Call and track
the tracker device for 10 times from cell phone in success, it
will make the cell phone number as the authorized number
automatically, and reply “add master ok”.
Send SMS “admin+password+space+cell phone number” to set up an
authorized number, the other authorized numbers should be set by
the first authorized number, if the number is successfully
authorized, the unit will reply“ admin OK” by SMS.
authorization: Send SMS “noadmin+password+space+authorized
number” to delete the authorized number.
6.6.4 If you would
like to track the target tracker device while aboard, please add
your country code in front of your number, e.g. admin123456
If there aren’t any
authorized numbers set-up, it will reply to all calls with a
location report. If there are authorized numbers set-up, it
won’t reply when the unauthorized number dials up it.
Dialing the tracker device from the authorized number, it will
hang up your calling and respond to a real-time latitude and
longitude report as following:
when no GPS signal, the SMS includes the last valid latitude &
longitude as well as the LAC code of current position, the LAC
code can be input in the column of “manual track” menu of web
platform to check location.
Tracker can send
automatic location reports at set intervals. If SMS mode is
active, reports will be sent as SMS text messages; if GPRS
tracking mode is active, update intervals to the server will be
6.8.1 Track with limited times upon time
Send SMS command
“fix030s005n +password” to the tracker device, it will report
the latitude & longitude at 30s intervals for 5 times. (s:second,
m:minute, h:hour). This command setting must be in 3 digits and
the maximum value is 255.
6.8.2 Track with unlimited times upon time
Send SMS “fix030s***n+password”
to the tracker device, it will reply the latitude & longitude
continuously at interval of 30 seconds.
Note: the interval
must not less than 20s.
6.8.3 Smart track upon time and distance
Please set "track with unlimited times upon time interval"
before this function, and then send "distance+password+space+distance",
tracker will reply "Distance ok", and then tracker will locate
upon both the pre-set time and distance.
"distance123456 0050", it means distance is 50 meters; the
number must be 4 digits Arabic numbers.
184.108.40.206 Set this
function on web server: Set time interval first and then
distance interval, tracker will locate upon the time and
6.10.4 Cancel: Send
SMS “nofix+password” to the tracker device to cancel the “auto
6.9.1 The tracker will update the positions
automatically to web server once the vehicle changing driving
direction over pre set angle value to form a smooth trajectory
consistent with the actual road, this function works only in
6.9.2 Send "angle+password+space+angle"
to tracker, it will reply" angle ok".
6.9.3 The angle must be
3 digits Arabic numbers, default angle value is 30 degree.
6.10.1 This function is deactivated as
default, send "suppress+password" to tracker, it will reply"
suppress drift ok". The GPS data stop updating if vehicle is not
driving (ACC is OFF) and latitude and longitude always keep
same, and GPS data updates automatically when vehicle is moving.
6.10.2 Cancel: send "nosuppress+password" to
tracker, it will reply" nosuppress ok ".
6.11 Exact street address by SMS
You must set up the APN of your local GSM network for the SIM
card in tracker first before using this function, if there is
user name and password for GPRS login, Please refer to 6.36 to
configure the APN, user name and password for GPRS login.
After configure the APN, send "address+password"
to device, it will reply SMS including exact address. For
example: No.113, Guankou 2nd Rd, Nantou, Nanshan district,
Shenzhen, Guangdong, china.
If the tracker cannot establish a solid
GPS Fix, it will calculate its location using Cell-id GSM
locating, location reports will include the GPS coordinates of
the last known position as well as a LAC code, Entering the LAC
code to the "Manual Track" menu of web tracking platform will
enable you see the tracker’s current location, you can also send
command “address+password" to the tracker to request exact
address. Tracker will automatically switch to tracking by LBS in
GPRS mode. Accuracy of LBS also known as Cell-id Tracking
depends on the GSM signal reception.
Note: This feature can be used normally in
most areas according to the signal of GSM network. It may not be
available in some areas.
The command to switch between Track
and Monitor are “tracker” and “monitor”.
6.13.2 The default mode is “track” (Track mode).
Send SMS “monitor+password” to the unit, and
it will reply “monitor ok!” and switch to “monitor” mode.
Send SMS “tracker+password” to the unit, it
will reply “tracker ok!” and restore to “track” mode.
the tracker device lost GSM signals or fall offline from GPRS,
it can store the tracking position and alerts automatically on
the flash drive onup the pre-set condition, when GSM signals is
re-established, all the event alerts will be auto-sent to the
authorized numbers or monitoring platform (server), but the
stored tracking data should be loaded to the monitoring platform
via SMS command.
Logging at preset times: Send SMS:
“save030s005n+password” to the tracker, it will reply “save ok”,
and will store the lat, long locations every 30 seconds for 5
times. (S: second, m: minute; h: hour).
SMS:”save030s***n+password” to tracker, it will reply “save ok”.
Logging Clearance: send SMS: “clear+password”
to tracker device, it will reply “clear ok”.
Logging Volume: Built-in flash drive
can save 16,000 positions.
The stored data in flash drive can be
download to computers through USB connection and then click menu
“Data Import” on web platform
www.gpstrackerxy.com to import the data to repeat its
6.15.1Current date Load: Send SMS: “load+
password” to tracker, it will reply: “load ok” if the device is
working well under GPRS mode; if not, it will reply “load fail!
Please check gprs” that means device does not work under GPRS
mode. Data only can be loaded to monitor platform by GPRS
6.15.2 Specified date Load: Send SMS: “load+
password+ space+ year month date” to tracker device, it will
reply: “load ok”. For Example: send SMS: “load123456 20110425”
to the tracker device, means to load the tracking data of 25th
April 2011 to monitoring platform.
6.16.1 Send SMS "forward+password+space+third
parties phone number" from authorized phone number, tracker will
reply"forward ok", and supports 1 third parties phone number at
For example, set the phone number of the
service provider of the simcard in the tracker, when charge
remind message coming in, tracker will forward it to authorized
6.16.2 Cancel: Send SMS command "noforward+password".
Send SMS command "balance+password+space+carrier’s
phone number+space+code" to tracker, it will forward the code to
carrier’s phone number and return the balance message received
from carrier’s phone number.
220.127.116.11 Send SMS “lowbattery+password+space+on”,
it will send SMS “low battery+latitude/longitude” to authorized
numbers 2 times in total at 15 minutes interval when voltage of
battery is going to be about 3.55V.
18.104.22.168 This function is activated by
default, send SMS “lowbattery+password+space+off” to deactivate.
22.214.171.124 Send “ extpower+password+space+on”
to activate, it will send SMS “power alarm+latitude/longtitude”
to authorized numbers every 3 minutes when external power is cut
126.96.36.199 This function is activated by
Cancel: Send SMS
“extpower+password+space+off” to deactivate it.
188.8.131.52This function is deactivated by
default, send SMS “gpssignal+password+space+on”, it will send
alert SMS “no gps+last valid latitude/longitude before lost
signal” when lost GPS signal.
184.108.40.206 Send SMS
“gpssignal+password+space+off” to deactivate
Long Press the SOS button for 3 seconds（For
model B, press button on
remote controller for 3 seconds）,
the tracker will send SMS “help me!+lat./long.” to all the
authorized numbers at interval of 3 minutes. It will stop
sending such a SMS when any authorized number reply SMS “help
me!” to the tracker.
Set up a geo-fence for the tracker to create
a safety zone. The tracker will send SMS to the authorized
numbers when it leaves this zone.
Set up: When the unit stays immobile in a
place for 3-10 minutes, you can send
to unit to set the restricted district. In case of breach, it
will send SMS “stockade!+ location” to the authorized numbers
Note: The first latitude & longitude is
coordinate of the top left corner of the Geo-fence, while the
second latitude & longitude is the coordinate of the bottom
right corner, it will alarm at interval of 3 minutes once leave
this restricted zone.
Cancel: Send SMS “nostockade+password” to
deactivate this function.
220.127.116.11 Set Area
Send SMS command "area+password+space+latitude,longitude+space+areaname,distanceM"
to tracker(distance unit: M for meter, K for kilometer), it will
reply "area01 ok".
Example: Send "area123456
Note: 5 areas at most and the distance
between two points can't be less than the total distance in the
2 commands, and different areas can't cover each other.
18.104.22.168 Delete areas
Send SMS command:"noarea+password+space+area
name", tracker will reply:"noarea ok".
22.214.171.124 Rename and set distance
Send SMS command "rename+password+space+old
name;new name,distanceM" to tracker, if name is not repeated and
area doesn't cover others, it will reply "rename ok!" for
Example: Send" rename123456
Area01;school,800M ", it means the new area name is "school",
and covers area of a radius of 800 meters.
126.96.36.199 Activate multi-area management
Send SMS command "area+password+space+on" to
tracker, it will reply "Area on ok!", when tracker enter or
leaves the pre set area, it will send SMS "area name+latitude &
longitude" to all the authorized phone number.
188.8.131.52 Deactivate Multi-area management
Send SMS command "area+password+space+off" to
tracker, it will reply"area off ok!"
184.108.40.206. Set up: when the unit stays
immobile in a place for 3-10 minutes with GPS signal reception,
you can send SMS“move+password+space+0200” to the tracker
(Suppose area of a radius of 200 meters, it supports 4 digits at
most. Unit: Meter). It will reply “move OK”. In case of such a
movement (the default distance is 200m), it will send SMS “Move+
latitude & longitude” to the authorized numbers at interval of 3
220.127.116.11 Cancel: Send SMS “nomove+password”
Set up: Send SMS “speed+password+space+080”
to the unit (suppose the speed is 80km/h), and it will reply
“speed OK!”. When the target moves exceeding 80km/h, the unit
will send SMS “speed+080!+ latitude & longitude” to the
authorized numbers at interval of 3 minutes.
Cancel: Send SMS “nospeed+password” to
deactivate the alarm.
Note: The recommended speed should be not
less than 30km/h. It may cause accuracy problem because GPS
signals drift if below that.
18.104.22.168This function is deactivated by
default. To activate this function, send "ACC+password" to
tracker, it will reply "ACC ok". And tracker will send "ACC
on+latitude & longitude" to authorized numbers when detect
ignition action, that means the vehicle has been started; and
tracker will send “ACC off+latitude & longitude" to authorized
numbers, that means ACC off.
22.214.171.124 Send "noACC+password" to deactivate
this function, tracker will reply "noACC ok".
126.96.36.199 This configuration can only activate
and deactivate the alarm to authorized numbers; it will send to
web server automatically in GPRS mode and can't be deactivated.
6.19.1 Send command “stop+password” to
tracker, tracker will execute it and reply “Stop engine
Succeed”. And it will remain immobile state until next command
6.19.2 Stop mode
188.8.131.52Execute immediately: Send command
“quickstop+password” to tracker, it will reply “quickstop OK”.
Then tracker will stop the car immediately after “stop” command.
184.108.40.206Execute depends on speed(Default
mode): Send command “noquickstop+password” to tracker, It will
reply “noquickstop OK”, Then the tracker won’t stop the car
immediately after “stop” command, instead, it will reply “it
will be executed after speed less than 20KM/H”, and stop the car
when the speed is less than 20KM/H.
6.19.3 Resume the Oil and Power System
send “resume+password" to tracker, it will
reply "Resume engine succeed", that means vehicle has resume the
Put the inductive key on
the top of the tracker as the picture showing:
6.20.1 ARM by
Put the inductive key on the top of the
tracker, LED blink 1 time, siren beeps 1 time, that means
tracker enters ARM mode.
6.20.2 DISARM by
Put the inductive key on the top of the
tracker, LED blink 2 times, siren beeps 2 times, that means
tracker enters DISARM mode.
6.20.3 Activate /
deactivate ARM by inductive key
ARM by inductive key is activated by default.
Send “keyarm+password+space+on” to tracker to
activate this function, and use the inductive key to ARM /
DISARM after received “keyarm on ok”.
Send “keyarm+password+space+off” to tracker
to deactivate this function, tracker will reply “keyarm off ok”.
Using the inductive key to switch the mode of
indicator, the mode switchs in circle as following table shows:
Blink 1 time
when driving and stop blink when parking.
times means succeed
times means succeed
Blink each 3
times means succeed
off and never blinks.
Press for 0.5
second, the siren will beep one time.
Press for 0.5
second, the siren will beep two times.
ARM & Silent
Press for 0.5
second when it is in disarm state, the siren
beep one time. No voice from
siren when alarm triggered and quit from siren mode
automatically when disarm.
Press for 3 seconds, Tracker will
send SOS alert to authorized phone numbers without
Press for 0.5 second when it is in
arm state, siren will beep 10 seconds, press disarm
button to quit.
Set up arm by SMS
Send “arm+password” to tracker, it will make
the car enter ARM states and and reply “Tracker is activated”.
If the car is in ignition (ACC is at “ON”
position), then the car can’t enter ARM state, reply “set up
fail! pls turn off ACC”.
Set up arm by remote
controller (Option, for model B ONLY)
Press button on
the remote controller for 0.5 seconds, the car enters armed
state and the siren will beep one time, no SMS reply.
If the car is in ignition (ACC is at “ON”
position), then the car can’t enter ARM state, and siren keep
6.24.1 Set up silent mode by SMS
Send silent+password to tracker, it will
reply silent ok! that means tracker enters
ARM & silent mode, siren won’t be sound after
alarm is triggered, but SMS alarm will be sent to authorized
Send disarm+password to quit ARM & silent
6.24.2 Set up silent mode by remote controller (Option for model
disarm state for 0.5 second, the siren will beep one time, the
car will enter ARM & Silent mode. Siren won’t be sound after
alarm is triggered, but SMS alarm will be sent to authorized
Press to quit.
6.25.1 DISARM BY SMS
Send command “disarm+password” to tracker,
tracker will be disarmed and reply “Tracker is deactivated”,
then it will turn off the alarm of shock sensor and ACC, and no
alarms if shock sensor and ignition triggered.
6.25.2 DISARM BY Remote controller (Option
for model B)
remote controller for 0.5 seconds, the car will enter DISARM
state and, siren beeps two times and tracker doesn’t send
The unit will send SMS “ACC alarm+lat/long”
to the authorized numbers at interval of 3 minutes when the
engine of the car is turned on, that is the key is rotated to
ACC.ON position to start the car in arm state; Siren will be
sound for 30 seconds, send “disarm+password” to stop it.
220.127.116.11 The unit will send SMS “Sensor
alarm+lat/long” to the authorized numbers when the sensor is
triggered in arm status; send “disarm+password” to stop it.
18.104.22.168 Shock sensor sensitivity
The sensitivity of the built-in shock
sensor has three different level:
First level: Alarm will be triggered after
detect slight vibration, send command"
Second level: Alarm will be triggered after
detect 8 times vibration in 2 seconds, send command"
Third level: Alarm will be triggered after
detect 25 times vibration in 5 seconds, send command"
When the car is in the place without GSM
network service, siren will be sound under non-silent mode if
alarm is triggered (shock sensor, ACC), but no SMS alarm will
send to authorized numbers.
Send SMS command “check+password” to the
tracker, It will reply the status of the power, battery, GPS,
ACC, GSM signal, GPRS status and oil to the authorized numbers.
For example: Send SMS “check123456” to the
tracker, It will reply following SMS.
GPS: OK/NO GPS
GSM Signal: 1-32 The higher digit it shows;
the stronger of GSM signals it receives.
Send SMS “reset+password” to tracker, it
will reply “reset ok”. And the GSM module and GPS module in the
tracker will be reset.
Send SMS command "sleep+password+space+time"
to tracker device, tracker will reply "sleep time ok" if none of
the alarms has been set and no operations, tracker will fall
asleep in 5 minutes, GPS module shuts down, LED will be off
,calling or SMS can awake the tracker. If these alarms have been
set, tracker will sleep by detecting shock sensor. (This mode
only works under SMS mode)
e.g. sleep123456 time
Send SMS command "sleep+password+space+shock"to
tracker, it will reply "sleep shock ok", and will enter sleep
mode if no vibration is detected, GPS module shuts down, LED
will be off . Shake or any operation can awake the tracker.
(This mode only works under SMS mode)
Send SMS command "sleep+password+space+deepshock"to
tracker to activate deep sleep by shock sensor, it will reply
"sleep deepshock ok", and will enter deep sleep mode if no
vibration is detected, GPS and GSM module shuts down, it will
run in supper lowest power consumption mode. Vibration or any
operation can’t awake the tracker. Alarms can be triggered
normally, after alarm cancelled, tracker come back to deep sleep
Send SMS command “sleep+password+space+off”
to tracker, it will reply “sleep off ok”. Tracker won’t sleep,
and GSM, GPS module keep working .This mode is the default mode.
to awake the tracker each hour, and location will be
automatically sent after wake up.(m: minute, h: hour, d:day).
The maximum time interval is 3 digits, and can’t exceed 30 days.
GSM and GPS shut down, tracker runs in supper lowest power
consumption, calling or sms can’t awake the tracker. Alarms can
be triggered normally, after alarm cancelled, tracker come back
to deep sleep mode again。
Cancel: after wake up, send
“noschedule+password” to deactivate this function.
Send SMS command "imei+password" to the unit.
E.g. Send SMS command "imei123456" to the tracker device, an
IMEI number in 15 digits will reply to your cell phone.
Send SMS command
“time+space+zone+password+space+time” to the tracker unit, If
succeed, It will reply “time OK”
For example: Send SMS “time zone123456 8”, 8
is Chinese time zone, If your country time zone is minus, send
SMS “time zone123456 -8”.
Send command: "gprs+password,0,0" switch back
to TCP mode, this is the default mode.
Send command:"gprs+password,1,1" switch to
Connect the gps tracker to computer with the
optional USB cable, open gps tracker’s flash drive and then open with notepad to operates according the tips.
Note: Correct password is necessary every
time to succeed in configuring the settings.
User must send SMS via cell phone to set up
IP, port and APN before starting GPRS.
22.214.171.124 APN standards for Access Point Name
and differs from country to country. For more information about
the local APN, inquire with your local GPRS network operator.
126.96.36.199 Text the tracker a SMS “APN+password
+ Space + your local APN” via a cell phone and if setup
successfully, the tracker will return the message “APN OK”.
188.8.131.52 e.g. send SMS command “APN123456
CMNET”. If succeeded, SMS “APN OK” returns from the tracker.
Notes: 123456 is tracker’s password and CMNET
is the APN of China Mobile (One of GSM Operator in China).
184.108.40.206 In most countries, the user name and
password involving GPRS login are not compulsorily necessary,
therefore, the entry can be skipped. For those countries
requiring user name and password, please configure as following:
220.127.116.11 Send SMS
“user,password ok” is returned by the tracker
18.104.22.168 For instance, send SMS “up123456
jonnes 666666” to the tracker, and if succeeded, the tracker
returns “user, password OK”
Note: 123456 is tracker device password,
jonnes is the user name for GPRS login, 666666 is the password
for GPRS login.
22.214.171.124. Send SMS via a cell phone: adminip
+password + Space + IP Address + Space + Port Number. If
succeeded, SMS “adminip OK” returns from the device.
126.96.36.199 e.g, Send SMS command “adminip123456
188.8.131.52 9000” to the tracker device, If succeeded,
“adminip OK” is returned by the device in SMS.( 123456 is
6.37.1 Tracker will change to less GPRS
traffic mode after parking 5 minutes, GPRS disconnect and
connect again when alarm being triggered or vehicle starts
6.37.2 Activate this function: Send "less
gprs123456 on", tracker will reply "less gprs on ok".
6.37.3 Deactivate this function: Send "less
gprs123456 off", tracker will reply" less gprs off ok".
Note: 123456 is the password of tracker, and
replace it with the new if you have changed.
6.38.1 The default mode is “SMS”
6.38.2 Send SMS “GPRS+password” to the unit,
and it will reply “GPRS ok!” It means tracker device has
switched to “GPRS” mode.
6.38.3 Send SMS “SMS+password” to the unit,
it will reply “SMS ok!” and restore to “SMS” mode.
6.39.1 Setup: send command
“centernum+password+space+number” to tracker, it will
reply“centernum ok”. After setup monitor center number, the sms
messages of auto track will be sent to this center number, if
events alarm need be sent to this number too, then this center
number must be setup as authorized number.
6.39.2 Cancel: Send “nocenternum+password” to
tracker, it will reply “no center num ok”.
6.40.1 Web based platform
www.gpstrackerxy.com. Configuration IP:
184.108.40.206 Port: 9000. Please check “software platform user
manual” included in the CD for detailed operation information.
6.40.2 PC based installation tracking
software user manual included in the CD in package.
Please comply with
the instructions to extend the unit life:
1. Keep the unit dry. Any liquid, i.e. rain,
moisture, may destroy or damage the inside circuitry.
2. Don’t use & store the unit in dusty
3. Don’t put the unit in overheated or
4. Handle carefully. Don’t vibrate or shake
5. Clear the unit with a piece of dry cloth.
Don’t clean in chemicals, detergent.
6. Don’t paint the unit, this may cause some
foreign materials left in between the parts.
7. Don’t disassemble or refit the unit.。
8. Please read the user manual carefully
before installation and operation, learn something more about
the voltage range. Otherwise, it won’t work properly or destroy
8. Faults & the Solutions
Fail to turn on
Please check out the power wiring
No GSM Signal
Please make sure SIM Card is GSM
Network and installed correctly; also call display
should be on; but no call transfer and PIN code off.
No GPS Signal
A more open view of the sky is
recommended to make sure the device can receive the
GPS signal normally.
SMS reply fail
Password incorrect or sms
commands in wrong format
Call without SMS reply or cannot
receive alarm SMS
Authorized number is wrong or
without setting any authorized number
Stop engine fail
Check the relay for engine cut is
Remote Controller fail
Turn off and turn on the device
and program again
Siren’s voltage is DC12V/24V/1A.
Siren can’t be activated if it is negative